Vista Ademco -10SE Průvodce řešením problémů stáhnout pdf (Strana 36)

Programming

g the Receiver and Transmitters

1. With at least one 2-line Alpha keypad (5137AD or 6139) connectedto the

Partition 1 terminals, power up the system temporarily. If you had

previously connectedthe AC transformer to the control paneI, you need

only plug in the transformer (to 120VAC outlet) to powerup the system.

2. Enter the programming modeby keying the following

Installer code(4112)+ 8+0+0.

3. *24. RF HOUSE ID CODE

The House ID identifies wirelesskeypads.

If a 5827 or 5827BD Wireless keypad is to be used, a House ID code

MUST be entered (01-31), and the keypad should be setto the sameID.

If no wirelesskeypad is to be used, enter “00”.

Partition 2 House ID is automaticallysetfor one number higher than the

ID number enteredfor Partition 1. Therefore, if a wirelesskeypad is also

used in partition 2, the House ID for partition 1 must not be higher than

30.

4. Press *56.

(ZoneProgramming Mode)

Use this mode to program zone numbers, zone types, partition numbers,

alarm report codes, and to learn RF devices for all wireless expansion

zonesthat are goingto be used in the system.

IMPORTANCE

wiredexpansionzonesarenot presentlybeing

usedin the system,but if thereis anypossibilim

thattheymaybeaddedat somefkturedate,you

shouldassignzonenumbersin the rangeof 16-

63for wirelesstransmitters.

Thereasonforthisis asfollows:wiredexpansion

zone numbers are restrictedto 10-17; if you

assign zone numbers between 10 and 17 for

wireless,and subsequentlyadd wiredexpansion

zones,

all serial numbers for wireless

transmittersin the 10-17 zone number range

will be lost. and any transmittersassignedto

thosenumbers will becomeinoperativein the

system.Theseparticulartransmitterswill then

have to be assignedMerent zonenumbers(in

therangeof 16-63)end their serialnumbersre-

learned.

Enter the zone number that you wish to

program. As an example, zone 20 is shown

entered.

You can assignzone

numbers to Ixansmittersas

follows:

●

Use zone numbers in the range of 10-63 if a

4219 or 4229 is NOT being used in the

system.

Use zone numbers in the range of 18-63 if a

4219 or 4229 IS ALSO being used in the

system,

even if some of the expansion unit’s

wired loops are not being used.

The actual number of zones that can be

assignedto wirelessis

24, but will be lessif a

wired expansion module is being used (see

“General Information” at the beginning of

this section).

Note:

M?ter

If using a button for arming, the zone

number assigned to the button is the

“user number” reported to the central

skm-rnstation, i.e., arm button = zone x,

disarm button = zoney.

entry of zone number, press [*I to

continue.

A summary display will appear, showing the

statusof that zone’sprogram.

If it is programmed satisfactorily, press [#l to

back up one step and enter another zone

number, if desired.

If the zone is not programmed, or you want to

change it, press [*]. A prompt for Zone Type

will appear.

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 119 120

Komentáře k této Příručce

Žádné komentáře

Vista Ademco -10SE Průvodce řešením problémů Strana 36

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Vista Ademco -10SE