Vista Ademco -10SE Průvodce řešením problémů stáhnout pdf (Strana 83)

General information

You must assign a zone type to each zone,which will then define the way in

which the systemwill respond to faults in that zone. Zone types are defined

below.

Type 00

Zone Not Used

~ 01

En&y/Exit Burglary #1

we 02

Entry/Exit Burglary W

Type03

Perimeter Burglary

Type04

Interior, Follower

Type05

Trouble by Day/

Alarm by Night

Progmuna zone with this zone@pe if the zone is not used.

This zone type providesexit and entry delayswhenever the zone is faulted if

the controlis armed in the Away or Stay modes.When the panel is armed in

the Instant or Maximum modes,no entry delay is provided. Entry delay #1 is

programmable,but Exit delay is automaticallysetas follows:

Exit Delay = Entry Delay (that has beenprogrammed) +40 seconds.

Exit delay begins whenever the control is armed, regardless of the arming

mode selected.This zone type is usually assigned to sensors or contactson

doorsthrough whichprimary en~ and exit will take place.

This zonetype providesa secondaryentry delay whenever the zone is faulted

if the panel is armed in the Away and Stay modes. When the panel is armed

in the Instant or Mazimum modes,no entry delay is provided. Enlz-y and Exit

delays#2 are automaticallysetas follows:

Entry delay #2= programmed Entry delay #1 + 30 seconds.

Ezit delay #2 = programmed Entry delay #1 + 40 seconds.

Exit delay #2 beginswhenever the controlis anneal,regardless of the arming

modeselected.

This zone type is usually assigned to sensorsor contactson doors through

which secondaryentry and ezit will take place, and where more time might

be neededto getta end from the keypad (typically used for a garage, loading

dock,or basementdoor).

This zonetype givesan instant alarm if the zone is faulted when the panelis

armed in the Away, Stay, Instant or Maximum modes. This zone type is

usually assignedto all sensorsor contactson exterior doorsand windows.

This zone type gives a delayed alarm (using the programmed Entry/Exit

time) if the Entry/Exit zone is faulted first. Otherwise this zone lype givesan

instant alarm. This zone type is activewhen the panel is armed in the Away

and Maximum modes.This zone me is bypassed automatically when

the panel is armed in the Stay or Instant modes. This zone type is

usually assignedto a zonecoveringan area such as a foyer,lobby, or hallway

through which onemust pazs upon entry (After faukiug the entry/exit zoneto

reachthe keypad to disarm the system.)

Sincethis zone type is designed to provide an instant slain if the enh-y/ezit

zoneis not violatedfirst, it will protectan area in the event an intruder hides

on the premises prior to the system being armed, or gains accessto the

premisesthrough an unprotectedarea.

This zone type will give an instant alarm if faulted when armed in the Away,

Stay, Instant or Msximum (night) modes. During the disarmed state (day),

the system will provide a latched tiouble sounding from the keypad (and a

central station report, if desired). This zonetype is usually assignedto a zone

which contains a foil-protected door or window (such as in a store), or to a

zone coveringa “sensitive”area such as a stockroom, drug supply room, etc.

This zone type can also be used on a sensor or contact in an area where

immediatenotificationof an entry is desired.

1 2 ... 78 79 80 81 82 83 84 85 86 87 88 ... 119 120

Komentáře k této Příručce

Žádné komentáře

Vista Ademco -10SE Průvodce řešením problémů Strana 83

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Vista Ademco -10SE